Just how do you actually feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably challenging job. If the old tub is readily obtainable, the job can move easily; if you need to open up a wall surface to eliminate the old tub and position the brand-new tub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the brand-new one. See to it you have certified on your own for the job as well as fit attempting it. Instead of employing a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may require a professional plumber to make tube connections.
This post will assist you set up a new bathtub in your restroom if you have already gotten a new tub as well as don't require to transform the setup of your previous supply of water pipelines.
Your tools as well as material list must make up the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bathroom should be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two taps making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing taps can be rather bothersome due to the restricted gain access to that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before moving on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bathtub up until the level checks out level.
To mount taps, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water system and examine all joints and brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub should wait until the tub has actually been made use of at least once as this will settle it into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers are in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The former type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, leading to complications with wetness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in use. The sealant can split rather early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the marketplace. It is suggested to fit the floor tiles using waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on A Step-by-Step Guide to Installing a Bathtub? Write feedback down the page. We would be interested to hear your suggestions about this posting. In hopes that you visit us again later on. Enjoyed reading our blog posting? Please share it. Let others locate it. I praise you for your time. Come back soon.
Rates